Magnetic Flow Meters

The ALMAGWP comes with an easy to read OLED display and is available with a wide variety of options, including AC or DC power, local or remote display, RS485, HART, and Profibus communications, as well as relay outputs. This broad array of options makes this general purpose mag meter an excellent choice for measuring conductive fluid flow rates in many applications and industries, including food and beverage, pulp and paper, and industrial process control.

The ALMAGWP comes with an easy to read OLED display and is available with a wide variety of options, including AC or DC power, local or remote display, RS485, HART, and Profibus communications, as well as relay outputs. This broad array of options makes this general purpose mag meter an excellent choice for measuring conductive fluid flow rates in many applications and industries, including food and beverage, pulp and paper, and industrial process control.

• Available in ⅜”~80″ (DN10~DN2000) line sizes
• Wide fluid velocity range of 0-39 ft/sec (0-12 m/s) with excellent low-flow accuracy.
• HART, RS485/Modbus Profibus-DP communications available
• Easy-to-read OLED display; visible in low light environments and in direct sunlight, no backlighting necessary.
• Optional IP68 enclosure; environmental protection class (submersible).
• Various liner materials are available to satisfy nearly all industrial applications.
• Excellent accuracy; ±0.5% of reading standard, ±0.2% of reading optional
• Upright/reverse flowrate test function standard with every unit.
• NIST traceable calibration certificate

From selection to pricing, our qualified team is ready to support you—request your quote today.

The ALMAGBAT’s display/converter module is equipped with a replaceable lithium battery that can be used for up to three years of continuous operation. The operation period can be extended by using a high-capacity battery instead of our standard lithium battery.

Remote communication with this battery powered mag meter can be achieved via a base-station-type radio communication network system. With a centrally located base station, the coverage radius can be up to 1000 meters. Base stations within a close proximity (SRD mode), may operate on 928 MHz frequency. For greater distances, GPRS or CDMA mobile network communications can be used to transmit data to any central office.

• Available in 1″ – 24″ (25-600 mm) line sizes
• 5 years with extended battery life (optional)
• GPRS, CDMA and SRD radio communications 
• Designed for clean water; fluid conductivity ≥ 20 μS/cm
• IP68 enclosure – tamper-sealed
• Available FEP liner suitable for vacuum applications
• Excellent accuracy; ±1% of reading
• Built-in pulse output for data-logging or telemetry
• Empty pipe detection
• NIST traceable calibration certificate

From selection to pricing, our qualified team is ready to support you—request your quote today.

SmartMeasurement’s ALMAG-IS is an insertion electromagnetic flow meter designed to measure the fluid velocity of conductive liquids in applications where hot-tap or insertion installations are preferred.

This insertion mag meter is available in four standard lengths and may be installed in any pipeline with internal diameters ranging from 2″ to 120″ (50~3000 mm) and in permanent locations where cost or space limitations preclude the use of inline meters.

The ALMAG-IS insertion magnetic flow meter is designed for use with conductive fluids including water, raw sewage, wastewater, clarified water, RAS, and WAS. Available process connections include hot-tapped, DIN and NPT threads.

• Applicable sizes: 2″~120″ (50~3000 mm)
• Operating pressure: = 230 psig (1.6MPa) max.
• Velocity range of 3-33 fps (1~10m/s)
• Accuracy: ±1.5%
• Hot-tap ball valve option allows sensor to be installed and retracted from process piping without shutting down the process
• Conductivity of measured medium: ≥ 20 μs/cm
• Electrode materials: 316L, Hastelloy, Ti, Ni, Tantalum
• Max. distance between sensor and converter: 165 feet (50 m)
• NIST traceable calibration certificate

From selection to pricing, our qualified team is ready to support you—request your quote today.

SMARTMEASUREMENT’s ALMAG-MN is an in-line electromagnetic flowmeter ideal for low flow of conductive liquids of 20 μs/cm or greater. The ALMAG-MN comes in sizes of 6, 8, 10mm tube sizes with process connection of ½” NPT or ½” BSPP.

The ALMAG-MN is designed for low-flow chemical injection or difficult to meter applications with pulsating metering pumps, corrosive fluids, food and beverage applications, etc.

The ALMAG-MN flow tube is available in ceramic, polyethylene or PEEK materials. The flow meter comes with a built-in temperature sensor, an integrated three-line display or in a blind version.

The ALMAG-MN can be used in areas where mechanical meters like turbines or paddle wheels cannot be used due to contamination/particulates in the fluid.

• Liners of PE, Peek or Ceramic
• Fluid velocity range of 0.01m/s – 10m/s, ideal for flow applications
• ½” NPT or BSP process connections 
• Ideal for extremely low flow applications
• Features a built in PT1000 temperature sensor; 0.1°F resolution
• Available with SS #316L or Hastelloy C electrodes
• High accuracy – ±0.5% of reading (Velocity > 0.6m/s) or ±3mm/s (Velocity ≤ 0.6m/s)
• Available with 4-20mA and 0-5KHz pulse and 2A relay outputs
• RS485 MODBUS; Optional for version w/ display, standard for blind version

From selection to pricing, our qualified team is ready to support you—request your quote today.

The ALMAGEG is an in-line electromagnetic energy flowmeter ideal for conductive liquids. A wide variety of sizes are available to accommodate nominal pipe diameters ranging from ½” through 120″. The ALMAGEG may be used in many applications that require accurate thermal energy measurement such as chilled water, hot water and condenser water systems. The ALMAGEG magmeter is available in a stand- alone configuration and may also be used with various SMC transmitter and display packages.

• Available with a wide range of liner materials
• Fluid Velocity range of 0-32 feet/sec, with good results for low flow applications
• Flange-type process connections are standard; ANSI, DIN, JIS style available
• Ideal for energy management applications
• Non-invasive measuring technique provides low pressure loss and excellent particle tolerance
• FEP liner available for vacuum pressure applications
• High accuracy – ±0.5% of reading standard or ±0.2% of range
• Bi-directional measurement
• Available with PT100 and PT1000 temperature sensors

From selection to pricing, our qualified team is ready to support you—request your quote today.

The SmartMeasurement ALMAG-HP is a high pressured electromagnetic flow meter designed to measure the flow rates of conductive liquids in applications with high operating pressures. The robust design of the ALMAGHP allows it to be used in applications with pressures in excess of 6000 psig (42 Mpa).

Line sizes ranging from ¼” to 8″ (6 mm to 200 mm) can be accommodated by the ALMAGHP high pressured mag meter, with available process connections including ANSI, DIN, and JIS-type flanges. A wide selection of options are also available for the display/converter module including integral or remote mounting, 110-220 VAC or 17-26 VDC power, and HART, RS485 and Profibus communications.

This high pressured electromagnetic flow meter’s unique ability to withstand high pressures, combined with its wide array of available features, makes it an ideal choice for many applications and industries. The ALMAGHP has been successfully used in high pressure fluid injection, steel, chemical, and mining operations, as well as a variety of industrial applications.

• Various liner/electrode material combinations can be selected in order to make this high pressure mag meter chemically compatibility with different fluids
• Capable of measuring fluid velocities of up to 40 feet/second (12 m/s), with a high turndown ratio
• Flange-type process connections are standard; ANSI, DIN, JIS styles available
• Suitable for high pressure operation in excess of 6000 psig
• IP68 protection class for submersible operation
• Available FEP liner suitable for vacuum conditions
• High accuracy – ±0.5% of reading (standard) or ±0.2% of range
• Diagnostic features alert the user to empty pipe or reverse flow conditions

From selection to pricing, our qualified team is ready to support you—request your quote today.

Subscribe to our bulletin and access valuable information about process optimization, equipment reliability, and new certified solutions from Lamar USA.